Deutsch English
Main page » Catalogue » AMPLIFIERS » OM-4000AREM Shopping Cart | Cash box
If you have and questions comments feel free to contact us at any time.

Call us
Mon - Fr from 09.00 - 18.00:

Telefon: +49 4346 / 601450

Shopping Cart
You do not have any products in your shopping cart yet.
Information about manufacturer  
OM-Power Homepage
More Products
       Advanced search
Remote Controller für OM4000A Need more information on this product? Please get in touch with us »
Remote Controller für OM4000A

General description of the OM 4000 A Remote control

Remote Control expands possibilities of using OM4000 A up to 10 meters away from your operating position.
When needed it is also possible to connect Remote Control unit to LAN network and control it using special software (not part of this package) to unlimited distance.

Warning: It is absolutely a must to observe and follow all best practices and safety precautions as well as your local health and safety law and fire / electricity regulations.
We do recommend using visual remote control like Web Camera etc.

Package includes:

    Remote control OM4000A
    Power supply 230V / 12V, 600mA
    10m patch lead to link Remote control with OM4000A PA

Label     Description
ON / OFF     - Standard ON / OFF switch. On state is indicated by green LED on the switch
OPERATE     - button controls the operating state of the PA. When i noperating mode green LED is lid
POWER     - Power LED indicates connection of power supply. 12V / 500 mA
FAULT     - Red Fault LED indicates fault on PA. It shall be lid on any fault condition!
STBY     - yellow LED indicates Stadby state of the PA
TUNE     - yellow LED will be lid if PI tuning circuit indicates that additional tuning is necessary
GRID     - indicates 2nd grid protection. Trigered if safe screen current has been reached )
SWR     - Yellow LED will indicate excessive reflected power on PA’s antenna socket
DRIVE     - will be lid if maximum drive power has been exceeded
OUTPUT POWER     - 30 segments bar graph will indicate peak output power
LAN     - Standard RJ45 connector - LAN Interface for remote access
ON     - Main ON / OFF switch. (Cut’s off 12V supply to unit)
DC 12V     - power jack (5,5 / 2,1) for supply of 12V / 600mA
CAL     - calibration potentiometer ( if necessary to synchronize the power bar graph with bar graph on OM4000A )
PA     - socket for direct connection to OM4000A PA

Warning: Please pay extra attention not to use PA socket as LAN socket as harmful voltages could damage your Ethernet devices such as switches, PCs etc.
Use only supplied 10m cable to connect your PA with Remote Control unit.


The Remote control box has to be grounded properly! Connect the screw on the rear panel of the box to your local grounding system with a copper-cable; use a cross-section of 4 mm2 at least.
Connect your transceiver and amplifier to the same grounding system of your shack carefully!
If you use a power amplifier with higher output you have to be aware that your grounding system works properly. All parts have to be grounded to the same system.
Use short cables and make sure that there are good contacts! Otherwise you run the risk of damaging your equipment, having problems with TVI/BCI or your signal may be distorted.

Deployment instructions:

    Connect unit with OM 4000A PA using supplied cable
    Supply 12V DC voltage to power socket using supplied PSU
    Check that green POWER LED and yellow STBY LED are both lid. Shall any connection fault occur it will be indicated by sequenced POWER and STBY flashing and FAULT led will be lid constantly.
    Turn the PA on using the ON button. Tube heating process will begin. This will be indicated by green LED on the ON button and by flashing of four LEDs (TUNE,GRID,SWR,DRIVE) (WAIT led will be also lid on the PA’s front panel)
    After heating process PA is now ready to be turned into operating mode using OPERATE button. Use same switch to enter STBY / OPERATE (works as reset shall fault state occur)

LAN Connection

Remote unit is interfaced to LAN via XPORT made by Lantronix (type XP1001000-05R). More info can be found at .

Default factory settings of XPORT are:

IP address: (first series can be:

These are strictly default settings. You can modify any of these by going to XPORT web GUI via your web browser.
We do not recommend changing any other parameters of the XPORT interface as loss of communication can be caused by doing so.
There is no default user name or password. It is highly recommended to secure web interface with username and password.

For remote control and monitoring over LAN special software is needed. It is available free of charge; it can be downloaded from the following address:

Need more information on this product? Please get in touch with us »
349,00 EUR incl. 19 % VAT
293,28 EUR export price - outside Europe

Conditions of Use Impressum Contact Data Protection Policy 

Secure Credit Card Payments by Saferpay
IBAN International Bank Transfer Master Card PayPal

Site Verfied by SiteLock


Website by: OCTIC

Parse Time: 0.024s