Deutsch English
Startseite » Katalog » ENDSTUFEN » OM4000A Warenkorb | Kasse
Service
Bei Fragen, Anregungen oder Problemen können Sie uns jederzeit kontaktieren.

Telefonisch erreichen Sie uns
Mo. - Fr. von 09.00 - 18.00 Uhr:

Telefon: +49 4346 / 601450
Email:info@appello.de

Kategorien
 TRANSCEIVER / Receiver
 ENDSTUFEN
 RX-FILTER INRAD
 TX-FILTER
 AUTOMATISIERUNG
 STATIONSZUBEHÖR
 ANTENNEN
 ROTOREN
 RX ANTENNEN
 MASTEN+ABSPANNUNGEN
 ANTENNENZUBEHÖR
 GEBRAUCHTGERÄTE
Warenkorb
Sie haben noch keine Artikel in Ihrem Warenkorb.
Hersteller Info  
OM-Power
OM-Power
OM-Power Homepage
Mehr Artikel
      Erweiterte Suche »
  Hersteller:
OM4000A Endstufe Sie haben Fragen zu diesem Produkt?  Nehmen sie sofort Kontakt mit uns auf »
OM4000A Endstufe

General description and the advantages of the OM4000A Amplifier

The OM Power model OM4000A is an automatic power amplifier, designed for use on all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes.

It is equipped with a two pieces of ceramic tetrode FU728F.

 

THE ADVANTAGES OF OM4000A

 

Full compatibility with:

  • - ICOM
  • - ELECRAFT
  • - KENWOOD
  • - TEN-TEC ORION
  • - YAESU
  • - Icom transceive protocol using by MicroHAM devices ( CI-V output )

 

Automatic switching between bands

Automatic tuning within the band according to segments

Automatic switching of band pass filter

Automatic switching of antenna switches

The possibility to use 2 different antennas within one band or segment


 

Specification of OM4000A:

Frequency coverage: Amateur Bands 1.8 – 29.7 MHz including WARC
Power output: 4000W in SSB and CW,
3000W in RTTY, AM and FM
Input Power: Usually 60 to 90W for full Output Power
Input Impedance: 50 Ohm, VSWR < 1.5 : 1
Power Gain: 17 dB
Output Impedance: 50 Ohm unbalanced
Maximum Output SWR: 2:1
SWR protection: Automatic switching to STBY, when reflected power is 350W or higher
Intermodulation distortion: 32dB below nominal output
Suppression of harmonics: < -50 dBc
Tubes: 2x FU728F Ceramic tetrode
Cooler: Centrifugal blower + Axial blower
Power supply: 2 x 230V – 50 Hz one or two phases
Transformers: 2 pcs of toroidal transformer 3kVA
Dimensions: 485 x 200 x 455mm (width x height x depth)
Weight: 46 kg
Protection circuits: - VSWR too high
  - Input power too high
  - Output power too high
  - Plate voltage too low
  - Anode current too high
  - Screen current too high
  - Grid current too high
  - Mistuning of PA
  - Hot switching protection
  - Soft start for protecting your fuses
  - “switch-on blocking “ at opened amplifier
LED indicators: - Current at control grid (Ig1) - 2 LEDs
  - WAIT – preheating of tube (150 sec.)
  - STBY - standby
  - OPR – operation mode
  - FAULT – failure, switching off for abt. 2 sec.
  - INHIBIT – operating condition
  - ANT 1 - which ANT is in use
  - ANT 2 – which ANT is in use
  - ANT - ANT selection
Bar graph indications: - Power output – 50 LEDs
  - Reflected power – 20 LEDs
  - Ig2 current - 10 LEDs
  - Anode voltage, anode current, tuning – 30 LEDs





 
Sie haben Fragen zu diesem Produkt?  Nehmen sie sofort Kontakt mit uns auf »
6.799,01 EUR incl. 19 % MWSt
5.713,45 EUR Exportpreis - ausserhalb Europa
 


AGB Impressum Index Kontakt Datenschutzerklärung 

Secure Credit Card Payments by Saferpay
IBAN International Bank Transfer Master Card PayPal

Site Verfied by SiteLock

Homepage-Sicherheit

Website by: OCTIC

Parse Time: 0.024s